RU
News from Anritsu(145)
News from Fluke(23)
News from Keithley(33)
News from Keysight Technologies(349)
News from Metrel(0)
News from National Instruments(145)
News from Pendulum(14)
News from Rigol(10)
News from Rohde & Schwarz(284)
News from Tektronix(157)
News from Texas Instruments(90)
News from Yokogawa(41)
Anritsu
Fluke
Keithley Instruments
Keysight Technologies
METREL
National Instruments
Pendulum Instruments
RIGOL Technologies
Rohde & Schwarz
Tektronix
Texas Instruments
Yokogawa
Login
Login:
Password:
Forgot your password?
Register
Information

TI's new high-voltage amplifiers enable accuracy in error-sensitive industrial applications

TI's new high-voltage amplifiers enable accuracy in error-sensitive industrial applications

07/31/2018

Texas Instruments (TI) introduced three new amplifiers with a unique combination of high speed and high precision, allowing designers to create more accurate circuits for error-sensitive applications. The new devices support more precise measurement and faster processing of a wide variety of input signals in test and measurement, medical, and data-acquisition systems.

Designers can select the amplifier architecture that meets their system requirements, with input voltages, bandwidths and key features as follows:

  • OPA2810: 27-V junction gate field-effect transistor (JFET)-input dual operational amplifier (op amp), 120-MHz bandwidth, 500-µV max offset voltage.
  • OPA189: 36-V zero-drift op amp, 14-MHz bandwidth, multiplexer (MUX) friendly.
  • THS3491: 32-V current-feedback amplifie

Wider bandwidth and faster speeds
Delivering up to twice the bandwidth and slew rate of competitive devices, TI's new high-voltage amplifiers enable the following system-level benefits:

  • The high bandwidths of the OPA2810 and OPA189 enable high-gain configurations and faster response times for more accurate measurements.
  • Designers can use the THS3491 current-feedback amplifier's wide small-signal bandwidth, high slew rate and output current of ±420 mA to achieve low distortion and high output power levels. The THS3491 is capable of 10-Vpeak-to-peak output levels at 200 MHz into 100-Ω loads for test and measurement systems, such as arbitrary waveform generators, laser diode drivers and high capacitive load drive applications.

Optimized precision for error-sensitive applications
The exceptional precisi­on of these high-voltage amplifiers maximizes system accuracy, while reducing the need for external calibration and minimizing bill-of-materials (BOM) cost. Precision benefits include:

  • With an industry-leading maximum offset and lowest voltage noise of 5.7 nV/√Hz for 27-V amplifiers in the 100- to 200-MHz bandwidth range, the OPA2810 op amp allows engineers to achieve more precise measurements in data-acquisition and signal-processing applications.
  • The OPA189 is the widest bandwidth zero-drift op amp with the lowest noise of 5.2 nV/√Hz. With a low maximum drift of 0.02 μV/°C, the OPA189 also minimizes temperature error without calibration, increasing system accuracy over an extended temperature range.

Lower power consumption
Consuming up to 80 percent less power than competitive devices, TI's new amplifiers enable low-power operation in high-speed designs:

  • The 120-MHz OPA2810 op amp offers best-in-class current consumption of 3.6 mA, while providing excellent signal-to-noise ratio and distortion.
  • Designed for applications that require high gain and low distortion in power-sensitive designs, the OPA189 is the lowest power zero-drift op amp with a 14-MHz bandwidth. This device enables engineers to design high-resolution, noise-sensitive industrial systems while only consuming 1.3 mA of quiescent current, which can benefit analog input modules, and battery and LCD test equipment.

www.ti.com


Company profile:  Texas Instruments

Back to the list


Related Information:

Current issue
#4 December 2021
KIPiS 2021 #4
Topic of the issue:
Modern instrumentation
Search